Starter · 3/8 in rod, steel BBs
bore Ø9.53 · OD Ø24.23 · width 7.14 mm · 6 steel BBs Ø4.5
The tested print: a deep groove bearing for a 3/8 in rod, 4.5 mm steel BBs in a crown cage.
Ball bearings for a rod or a shaft on steel or airsoft BBs, needle thrust bearings on needles cut from filament and crossed roller slew rings. Each opens in the Printed Bearing Designer in 3D, every setting in place and ready to change. Looking for something else? See the timing pulley, sprocket and gear samples.
bore Ø9.53 · OD Ø24.23 · width 7.14 mm · 6 steel BBs Ø4.5
The tested print: a deep groove bearing for a 3/8 in rod, 4.5 mm steel BBs in a crown cage.
bore Ø8 · OD Ø22.7 · width 7.14 mm · 5 steel BBs Ø4.5
A 608-sized job for an 8 mm shaft, 4.5 mm steel BBs.
bore Ø10 · OD Ø27.7 · width 8.64 mm · 5 airsoft BBs Ø6
Plastic airsoft BBs as the balls: quiet and cheap, for light loads.
bore Ø12 · OD Ø26.7 · width 12.64 mm · 14 steel BBs Ø4.5 in two rows
Two rows of steel BBs for more load and less tilt.
bore Ø8 · OD Ø22.7 · width 7.14 mm · 5 steel BBs Ø4.5 · flange Ø26.7 × 1.5 mm
A flange round the outer race's bottom face, as a flanged F608: it stops the bearing going through its hole.
bore Ø8 · OD Ø22.7 · width 7.14 mm · 5 steel BBs Ø4.5 · hexagon
A hexagon outer race that sits in a hex pocket and can't turn.
bore Ø8 · OD Ø25.7 · width 7.14 mm · 5 steel BBs Ø4.5 · semicircle groove 3 wide, 1.5 deep
A semicircle groove round the outside for a 3 mm O-ring belt.
bore Ø8 · OD Ø22.7 · width 7.14 mm · 5 steel BBs Ø4.5 · pillow block, centre 20 mm above the base (raised from the 11.35 mm minimum)
The outer race is its own pillow block, raised: its centre height set to 20 mm above the base, well above the 11.35 mm minimum (the base just touching the race). Any centre height from the minimum up can be set. A bulged top and two hold-down feet for M3 screws.
bore Ø8 · OD Ø22.7 · width 7.14 mm · 5 steel BBs Ø4.5 · pillow block, centre 11.35 mm above the base (the minimum)
The pillow block at its lowest: the bearing's centre 11.35 mm above the base, half the outside diameter, so the base just touches the race. Raise it to any height above this (see the raised pillow block). A bulged top and two hold-down feet for M3 screws.
hex bar bore 12.7 across flats · OD Ø29.43 · width 7.14 mm · 8 steel BBs Ø4.5
A bearing that rides on 1/2 in hex shaft.
bore Ø8 · OD Ø27.7 · width 7.14 mm · 5 steel BBs Ø4.5 · semicircle groove 5 wide, 2.5 deep
A deep semicircle groove round the outside for a 5 mm round (O-ring cord) belt, 2.5 mm deep.
bore Ø11.2 · OD Ø28.2 · width 7.14 mm · 7 steel BBs Ø4.5 · involute spline m1 × 12 teeth, 30°
A bearing for an involute splined shaft: module 1, 12 teeth, 30°.
bore Ø5 · OD Ø19.7 · width 7.14 mm · 4 steel BBs Ø4.5 · D-flat 0.5 deep
A bearing that keys onto a stepper motor's 5 mm D-shaft, its flat 0.5 mm deep.
bore Ø8 · OD Ø27.2 · width 7.14 mm · 5 steel BBs Ø4.5 · V groove 4.5 wide, 2.25 deep
A 90° V groove 2.25 mm deep round the outside, for a V belt or a guide rail.
bore Ø8 · OD Ø25.7 · width 7.14 mm · 5 steel BBs Ø4.5 · square groove 3 wide, 1.5 deep
A square groove 3 mm wide and 1.5 mm deep round the outside, for a retaining ring or a flat belt.
bore Ø9.53 mm · 13 needles Ø1.75 × 10 mm · flanged races
Needles cut from 1.75 mm filament between two flanged races.
bore Ø9.53 mm · 9 needles Ø2.85 × 10 mm · a cup with snap catches
Thicker 2.85 mm filament needles in a cup that snaps shut.
bore Ø200 mm · 212 needles Ø1.75 × 10 mm · a cup with snap catches
A large flat needle thrust bearing: 1.75 mm filament needles 10 mm long, in a cup with snap catches, on a 200 mm bore.
bore Ø30 · OD Ø79.75 · width 11.84 mm · 20 rollers Ø6 · spacers A and B · M3 bolts: 8 inner, 12 outer
Printed tapered rollers crossed at 90°, spacers A and B between them, M3 bolts.
bore Ø60 · OD Ø120.66 · width 11.89 mm · 36 rollers Ø6 · spacers A and B · M4 bolts: 8 inner, 12 outer
A larger slewing ring with flat-head M4 bolts in countersinks.
Designing is free; the STL and STEP files download from the app for tokens, and the fit coupon is free. Print the fit coupon first, so the bearing fits your printer.